Firwood 2504 Water Borne Concrete Floor Seal

Clear acrylic concrete floor seal to reduce dusting of factory and warehouse floors. Apply by brush or roller

Firwood 2504 Water Borne Concrete Floor Seal

Step 1. Click on required shade

Actual colors may vary from the color on your screen due to monitor color restrictions. Always use a shade card for colour matching purposes.

Step 2. Select Options

£25.25 each [+VAT]
+ 25 Loyalty Points

Add to wishlist

Professional Users - Please register for a trade account for regular purchases. Click here to apply for an account.

Firwood 2504 is a clear concrete floor seal, water borne, single pack acrylic. It possesses good abrasion resistance and resists staining. It also acts as a dust proofer making cleaning much easier. Simple to apply by brush, roller or squeegee. Quick drying. Not suitable for power floated floors or for application to self leveling screeds.

Firwood 2504 is formulated for use on concrete stone and brick floors. Suitable for areas subject to general industrial use. Internal use only.

  • Easy to apply
  • Water borne product
  • Helps reduce dust on concrete floors
  • Suitable for industrial and commercial applications
Coverage: Approximately 35m² per 5 litre per coat. Normally 2 coats are required.
Typical Applications:
  • Warehouses
  • Factory Floors
  • Production Areas
  • Showrooms
  • Garages
Slip Resistance. (Results obtained using BS7976 Four S Pendulum Test):

  • Dry : 58 - Low slip potential Wet : 33 - Moderate slip potential
Compliance: Complies with “the VOC in Paints, Varnishes & Vehicle Refinishing Products Regulations 2005". EU limit value for this product (cat A/i): 140g / litre (2010)

For more information please also see the Flooring products selection guide located in the download tab.

Please refer to Material Safety Data Sheet and Technical Information Sheet prior to the use of this product. See download tab.

Application Methods: Apply product by brush or double arm roller. Can also be applied using a squeegee with rubber blade.

Colour Availability: Clear

Pack Size: 5 & 25 Litres

Drying Time @ 20ºC: Drying times will be extended at low temperatures . Do not apply when ambient temperature falls below 10ºC or relative humidity exceeds 85%.

Surface Dry @ 20ºC : 30 minutes

Hard Dry @ 20ºC: 1 hour

Over Coat @ 20ºC: After 24 hours. Foot traffic can be allowed on the coated area after 24 hours and heavier traffic after 72 hours.

Coverage: Approximately 35m² per 5 litre per coat. Normally 2 coats are required.

Flash Point: Not applicable

VOC Content (as supplied): Max 70g / litre

Storage: Store in temperature range 5-40ºC

Thinners: Use clean cold water

Surface preparation: Refer to the Technical Data Sheet.

Mixing: Mix thoroughly for approx. 5 mins using a wide bladed- stirrer.

Directions for Use: Best results are obtained in warm (minimum 15°C), dry conditions with a good through draught. Apply using a brush and/or long pile, double arm roller. Can also be applied using a squeegee.

On bare concrete floors: It is recommended that the first coat be diluted with up to 10% water by volume prior to application. This will help seal the concrete surface. Once dried, a second coat can be applied at full strength.

On concrete floors any surface laitance must be removed prior to painting. We recommend the use of Firwood 2709 Concrete Etching Fluid for this.

On previously painted floors: It is recommended that two thin coats be applied rather than one thick coat. This will prolong the life and performance of the coating.

Excessively thick coatings will dry to a milky white appearance and are prone to softening when wet. The performance of the sealer is adversely affected by the application of excessively thick coatings. Two thin coats are better than one thick application.

Cleaning: Application equipment should be washed immediately after use in clean cold water.

Please click here to download the Technical Information Sheet PDF.

Please click here to download the Material Safety Data Sheet PDF.

Please click here to download the Flooring products selection guide PDF.

Product Reviews
Water Borne Concrete floor seal
By Steve from Tottington on October 2nd 2015
Quick and easy to apply, enhances the colour of my stone on the drive, knowing this product is environmentally friendly gave me peace of mind to use it. Looking forward to the weed free summers
Sign Up for Email Offers
Close Chat Now boldchat