Firwood 2217 Rapid Set Epoxy Repair Mortar

Firwood 2217 Rapid Set Epoxy Repair Mortar

Fix holes and cracks in factory floors with this quick setting epoxy repair mortar. Easy to mix and apply





Professional Users - Please register for a trade account for regular purchases. Click here to apply for an account.

Select Options

£30.25 each [+VAT]
+ 30 Loyalty Points
Volume discounts available

5+ for £29.05 each [+VAT]

Add to wishlist

Professional Users - Please register for a trade account for regular purchases. Click here to apply for an account.

Fast curing tough epoxy mortar repair system for cracks and potholes in concrete floors. High compressive strength suitable for both vehicular and fork lift traffic. Ready for traffic after 3-4 hours when cured at 20° C. Easily mixed three component system.

Best used for holes 5mm deep to 50mm deep in concrete and stone. Cut out all loose material and form a suitable edge to apply mortar up to. Three component product is easily mixed by a power drill and mixer attachment or by hand and trowel on a sheet of plywood. Quick to both prepare and apply, a cost effective solution for smaller floor repairs.

  • Suitable for indoor and outdoor use
  • Cures to a hard finish that is suitable for vehicles and fork lift trucks
  • Can be applied to a feathered edge
  • Trowel out to a smooth finish with minimal shrinkage on curing
Coverage: Approx 2.5 litres per 5 kilo pack Equivalent to 025m2 at 10mm application thickness

Typical Applications:
  • Concrete Floors
  • Steps
  • Ramps
Please refer to Material Safety Data Sheet and Technical Information Sheet prior to the use of this product. See download tab.

Application Methods: Apply by trowel or Float. Clean application equipment immediately after use

Colour Availability:
Grey

Pack Size: 5 & 10 kgs packs

Drying Time @ 20ºC: Drying times will be extended at low temperatures . Do not apply when ambient temperature falls below 5ºC or relative humidity exceeds 90%.

Hard Dry@ 20ºC: Approx 4 hours. Approx 12 hours@5°C Drying times will be extended at low temperatures.

Coverage: Approx 2.5 litres per 5 kilo pack Equivalent to 025m2 at 10mm application thickness

Flash Point: Not applicable

VOC Content (as supplied): Max 5g / kilo

Storage: Store in temperature range 5-40ºC

Thinners: Firwood 114 Thinners for cleaning application equipment

Pot Life @ 20ºC:1 hours when mixed. Use mixed product within the hour. The pot life will be significantly reduced where the mixed paint is used at higher ambient temperatures.

Packaging: Pack Size: 5 and 10kg pack A 5kg pack consists of the following: 1 can Part A base, 1 Can Part B Cure, 1 Bag Aggregate, 1 Solvent spray for wetting of tools, Application Instructions and outer mixing vessel. For 10kg packs each pack consists of the following: 2 can Part A base, 2 Can Part B Cure, 2 Bag Aggregate, 1 Solvent spray for wetting of tools, Application Instructions and outer mixing vessel.

Directions for Use: Prepare the area to be filled before mixing the mortar.

Ensure the surface to be coated is clean, dry and free from grease water and oils.

If the concrete is crumbling then be careful to remove all loose pieces. Best results are achieved by chipping out any crumbling concrete and forming a suitable edge to work to. Sweep out any loose material.

Apply in dry conditions where precipitation is not expected during the application and drying time of the mortar.

The mortar can be used to create a feather edge but it is always best to cut away the edge to strengthen the joint between old and new surfaces.

Remove all components and instructions from the plastic outer bucket.

Take a tin of the base epoxy marked A and pour this into the outer plastic pack. Pour a tin of curing agent marked B slowly into the base and mix well. This is best done with an electric drill and suitable mixer blade.

Immediately start adding a bag of sand to mix the mortar. Add slowly to ensure all the sand gets wetted out by the epoxy resin mixture. Continue mixing until a homogenous mix has been made. All the sand must be wetted out and appear grey.

For the 10 kg pack it is best to split into two units of 5 kgs being 1 bag sand, 1 tin part A base and 1 tin part B curing agent per mix. A more powerful mixer will be required if mixing the full 10 kg pack in one mix.

Apply to the hole or crack using a steel trowel or float. Compact down particularly at the edges to ensure a good joint between old and new surfaces.

Apply by use of the solvent spray (Supplied in the pack) a small amount of solvent to the trowel. This prevents drag on the trowel to help smooth out the mortar.

Protect the applied product from foot and vehicle traffic until fully cured. Cover if rain is expected in the drying period. When making up multiple mixes empty the mixing bucket before starting a further mix.

Cleaning: Application equipment should be cleaned using Firwood 114 thinners immediately after use.

Please click here to download the Technical Information Sheet PDF.

Please click here to download the Material Safety Data Sheet for the base component PDF.

Please click here to download the Material Safety Data Sheet for the curing agent PDF.
Product Reviews
Tough product
By Stuart Beardall from Manchester on August 7th 2015
review
Used this on our workshop floors for a couple of years and it has performed well. Sets quickly and we can drive over it the next day.
Don't forget...
Firwood 2750 Two Pack Fast Dry Water Borne Epoxy Floor Seal

From £ 65.52

Paint Mixer

From £ 7.96

Bucket Trowel

From £ 5.26

Sign Up for Email Offers
Close Chat Now boldchat