Firwood 2530 Water Borne Polyurethane Wood Floor Seal

Single pack durable polyurethane wooden floor sealant. Can also be used on doors, trim and panelling

Firwood 2530 Water Borne Polyurethane Wood Floor Seal

Step 1. Click on required shade

Actual colors may vary from the color on your screen due to monitor color restrictions. Always use a shade card for colour matching purposes.

Step 2. Select Options

£36.00 each [+VAT]
+ 36 Loyalty Points

Add to wishlist

Professional Users - Please register for a trade account for regular purchases. Click here to apply for an account.

A colourless water borne single pack polyurethane lacquer. Low odour formulation suitable for many types of wood to enhance and protect. Excellent on wood trim, internal doors and domestic wood flooring. Avaiable in full gloss, satin and matt finishes. This product is quick drying and has good abrasion resistance. It can be applied as a single pack coating. Normally two to three coats are required. For high traffic flooring applications one or more coats of Firwood 2550 two pack water borne floor seal can be applied as a finishing coat.
Available as an anti-slip coating with the addition of Firwood 209 - Polymer beads.

  • Low odour formulation
  • Quick drying
  • Good abrasion resistance
Coverage: 10m² per litre on planed wood. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.
Typical applications:

  • Trim
  • Wood Doors
  • Panelling
Slip Resistance. Results obtained using BS7976 Four S Pendulum:
  • Dry : 71 - Extremely low slip Potential Wet : 25 - Moderate slip potential
Slip Resistance (with the addition of anti-slip Aggregate)Results obtained using BS7976 Four S Pendulum Test:
  • Dry 95 - Extremely low slip potential Wet : 43 - Low slip potential
Compliance: Complies with “the VOC in Paints, Varnishes & Vehicle Refinishing Products Regulations 2005".
EU limit value for this product (cat A/i): 140g / litre (2010)

For more information please also see the Flooring products selection guide located in the download tab.

Please refer to Material Safety data Sheet and Technical Information Sheet prior to the use of this product. See download tab.







Application Methods: Roller, Brush. When wet, the lacquer has a milky white appearance which becomes clear when dry.

Colour Availability: Clear - Satin

Pack Size: 5 litres

Drying Time @ 20ºC: Drying times will be extended at low temperatures . Do not apply when ambient temperature falls below 10ºC or relative humidity exceeds 80%.

Surface dry @ 20ºC : 30 minutes. Dry for sanding after approx. 8 hours.

Hard Dry@ 20ºC: 1 hour

Coverage: 10m² per litre on planed wood. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

Flash Point: Not applicable

VOC Content (as supplied): Max 139g/ litre

Storage: Store in temperature range 5-40ºC

Thinners: Use clean cold water

Directions for Use: All surfaces should be clean, dry and free from dust, grease, waxes, etc.

To ensure consistency of gloss level, mix thoroughly for approx. 5 mins using a wide bladed stirrer. Untreated wood may be primed with this lacquer by diluting with water 20%. Subsequent coats should be applied without thinning.

Previously lacquered surfaces must be cleaned carefully of dirt and grease and lightly abraded.

Bare spots must be primed before lacquering the whole surface.

When coating floors, heavy traffic should be avoided on newly painted surfaces for a period of 72 hours after painting.

Where masking tape is used, it is recommended that it be removed immediately after application of the coating to prevent tearing of the coating film and produce a clean edge.

Cleaning: Wash application equipment immediately after use. Use clean cold water.






Please click here to download the Technical Information Sheet PDF.

Please click here to download the Material Safety Data Sheet PDF.

Please click here to download the Flooring products selection guide PDF.

Product Reviews
Thanks for the excellent service
By Tanya Hamilton from Birmingham on July 21st 2015
review
Just purchased this for a chipboard floor. Thanks for the excellent service. The goods arrived the next day and we applied the seal last weekend. Looks great and was easy to apply with very little odour. Brushes just washed out under the tap!
Don't forget...
Firwood 209 Polymer Beads

From £ 8.15

Double Arm Roller Kit

From £ 29.64

Firwood 2550 Two Pack Water Borne Polyurethane Floor Seal

From £ 52.00

Sign Up for Email Offers
Close Chat Now boldchat