Solvent free epoxy line marking paint with excellent durability.Can be applied to bare concrete and previously painted surfaces. Tough finish that develops good chemical resistance. Supplied as a kit with 1 roll of masking tape, 2" paint brush, gloves and stirrer.
Recommended for heavily trafficked areas including fork lift trucks. Must be applied to a sound clean substrate. Two pack material, mixing required prior to application. Coverage approx 75m x 5cm line per pack. Coverage will vary depending on substrate applied to and film thickness.
Hard wearing
Fast curing
Two pack solvent free epoxy system
Can be applied at low temperatures
Coverage: Approx 40 metres of 7.5 cm wide line per pack. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.
Typical Applications:
Factories
Ports
Theme Parks
Railways
Compliance: Complies with "the VOC in Paints, Varnishes & Vehicle Refinishing Products Regulations 2005". EU Limit Value for this product (cat.A/j): 500g/l (2010). This product contains max 5 g/l VOC.
For more information please also see the Flooring products selection guide located in the download tab.
Please refer to Material Safety Data Sheet and Technical Information Sheet prior to the use of this product. See download tab.
Application Methods: Apply product by brush or roller. Use lambswool rather than foam rollers.
Colour Availability: White, Yellow & Black
Pack Size: 1.6 litre Composite pack consist
ing of Part A: Base, Part B: Cure, Pack also contains 1 roll
of masking tape, 1 off 2" paintbrush, 1 off pair of gloves and 1 off stirring stick
Drying Time @ 20ºC: Drying times will be extended at low temperatures . Do not apply when ambient temperature falls below 10ºC or relative humidity exceeds 85%.
Hard Dry @ 20ºC: 4 - 6 hours
Coverage: Approx 40 metres of 7.5 cm wide
line per pack. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.
VOC Content (as supplied): VOC Free
Storage: Store in temperature range 5-40ºC
Pot Life@ 20ºC: 30 minutes when mixed. The pot life will be significantly reduced where the mixed paint is used at higher ambient temperatures.
Surface preparation: Refer to the Technical Data Sheet.
Mixing Ratio:
Base : Curing Agent 1.12:0.4
by volume
Packaging: Mixed paint volume 1.6 lt. Composite pack consisting of Part A: Base, Part B: Cure,Pack also contains 1 roll of masking tape, 1 off 2" paintbrush, 1 off pair of gloves and 1 off stirring stick
Mixing:: As the pot life for this product is
only 30 minutes, the components should only be mixed together
when ready to apply the coating.Do not mix until all surface preparation has been completed. Add Part B - Cure to Part A - Base
and mix thoroughly for approx. 5 mins using the stirring stick provided.
Caution: The base paint cures by exothermic reaction with the curing agent. After mixing the base paint will increase significantly in temperature. The product is usable in this state but care should be taken in its handling. Do not leave the can on any surface that might be affected by high temperatures and hold the can with suitable heat protection.
Directions for Use: Best results are obtained in warm (minimum 15°C), dry conditions with a good through draught.
Mask off the areas to be coated as applicable. Apply the mixed
base paint to the surface using a brush and/or short nap roller.
Remove masking tape whilst coating is still wet. Ideally the product should be applied as a single coat application.
Cleaning: Application equipment should be disposed of after use.
Please click here to download the Technical Information Sheet PDF.
Please click here to download the Material Safety Data Sheet for the base component PDF.
Please click here to download the Material Safety Data Sheet for the curing agent PDF.
Please click here to download the Flooring products selection guide PDF.
Product Reviews
Don't forget...
Firwood 2202 Two Pack Fast Dry Epoxy Floor Seal - Composite Pack