Firwood 94 Single Pack Epoxy Gloss

Tough epoxy ester gloss paint for concrete and wood floors. Can also be used for general metal fabrications

Firwood 94 Single Pack Epoxy Gloss

Step 1. Click on required shade

Actual colors may vary from the color on your screen due to monitor color restrictions. Always use a shade card for colour matching purposes.

Step 2. Select Options

£61.00 each [+VAT]
+ 61 Loyalty Points
Volume discounts available

5+ for £52.45 each [+VAT]
10+ for £44.00 each [+VAT]

Add to wishlist

Professional Users - Please register for a trade account for regular purchases. Click here to apply for an account.

A tough epoxy gloss finish with good adhesion and flexibility. Has good resistance to water, oils and greases. Fast drying and easy to apply by brush or roller. This product can be used on concrete, wood and steel surfaces in both interior and exterior locations, making it an ideal single pack coating for multi-surface application. Suitable for pedestrian and light/medium wheeled traffic areas.

  • Use as an anti-slip coating by the addition of Firwood 204 Anti-slip aggregate prior to application
  • Hard wearing solvent borne coating
  • Over 300 shades available from stock
  • Single pack
  • Easily applied by brush or roller
Coverage: Approximately 65m² per 5 litres per coat. Normally two coats are required. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

Typical Applications:

  • Factory Floors and Workshops
  • Garages
  • Showrooms
  • Schools
Slip Resistance (As supplied) Results obtained using BS7976 Four S Pendulum Test:

  • Dry : 52- Low slip Potential Wet : 41 - low slip potential
Slip Resistance (with aggregate) Results obtained using BS7976 Four S Pendulum Test:

  • Dry : 70- Low slip Potential Wet : 14 - low slip potential
Compliance: Complies with “the VOC in Paints, Varnishes & Vehicle Refinishing Products Regulations 2005". EU limit value for this product when used as a binding primer (cat A/h): 750g / litre (2010) and (cat A/i): 500g / litre (2010) when used as a one pack performance coating.

Colours in this range are produced upon receipt of order and are not accepted for return unless faulty. Where accurate colour matching is required please request a shade card as online colour charts are not always represented accurately.

For areas subject to heavy traffic refer to Firwood 2700.

For more information please also see the Flooring products selection guide located in the download tab.

Please refer to Material Safety Data Sheet and Technical Information Sheet prior to the use of this product. See download tab.



Application Methods: Apply product by brush or roller using a long pile, double arm roller.

Colour Availability: 300 + Shades including British and RAL standards

Pack Size: 5 litres

Drying Time @ 20ºC: Drying times will be extended at low temperatures . Do not apply when ambient temperature falls below 10ºC or relative humidity exceeds 90%.

Surface dry @ 20ºC : 1 ½ hours

Over Coat@ 20ºC: After 24 hours

Coverage: Approximately 65m² per 5 litres per coat. Normally two coats are required. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

Flash Point: 38ºC

VOC Content (as supplied): Max 499g / litre

Storage: Store in temperature range 5-40ºC

Thinners: Firwood 143 Thinners



Surface preparation: Refer to the technical Data Sheet.

Mixing: Mix thoroughly for approximately 5 minutes using a wide bladed stirrer.

For Anti-Slip Surfaces: For anti-slip surfaces, add Firwood 204 - Anti-slip aggregate and ensure the grit is evenly dispersed throughout the mix before and during application.

Directions for Use: Best results are obtained in warm (minimum 15°C), dry conditions with a good through draught. Apply using a brush and/or long pile, double arm roller.

Bare concrete floors. It is recommended that the first coat be diluted with approx. 10-20% Firwood 143 Thinners by volume prior to application. This will act as a binding primer and help seal the concrete surface. Once dried, a second coat can be applied at full strength. Do not flood pour paint onto substrate.

Previously painted floors. it is recommended that two thin coats be applied rather than one thick coat. This will prolong the life and performance of the coating.

Wooden flooring. two coats are required to produce a smooth finish. Do not apply excessively thick coats as this will lead to slow drying and possible wrinkling of the finished application. It is better to build up the film with multiple thin coats rather than one heavy coat. Allow each coat to dry hard prior to the application of additional coats.

Cleaning: Application equipment should be cleaned using Firwood 143 thinners.

Please click here to download the Technical Information Sheet PDF.

Please click here to download the Material Safety Data Sheet PDF.

Please click here to download the Flooring products selection guide PDF.

Product Reviews
Hard wearing with visual impact
By Steve Birch from Lancashire on March 25th 2015
review
We use Firwoods grey floor paint (RAL 7045) within most of our factory areas and find it to be particularly hard wearing and durable. When combined with the other elements of colour used within the factory, it creates the impressive visual impact that we aim to convey to all of our customers from the moment that they walk through the door.
Don't forget...
Double Arm Roller Kit

From £ 29.64

Firwood 204 Anti-Slip Aggregate

From £ 3.84

Paint Stirrer

From £ 1.98

Firwood 143 Thinners

From £ 17.65

Sign Up for Email Offers
Close Chat Now boldchat