Firwood 2750 Two Pack Fast Dry Water Borne Epoxy Floor Seal

Gloss finish two pack water borne epoxy floor seal available in over 250 RAL and BS shades from stock. Suitable for commercial environments

**Special Offer** Buy RAL 7042 for Only £65.52 + VAT
Firwood 2750 Two Pack Fast Dry Water Borne Epoxy Floor Seal

Step 1. Click on required shade

Actual colors may vary from the color on your screen due to monitor color restrictions. Always use a shade card for colour matching purposes.

Step 2. Select Options

£89.46 each [+VAT]
+ 89 Loyalty Points

Add to wishlist

Professional Users - Please register for a trade account for regular purchases. Click here to apply for an account.

Available from stock in over 250 BS 4800 and RAL shades, this fast drying water borne epoxy floor seal is tough and hard wearing. Low odour formulation is ideal for food, medical and animal environments. Quick dry properties permit two coats to be applied in the same day reducing down time for factories and public buildings. Recommended for use where a durable full gloss floor seal is required. Suitable for medium to heavy duty applications including fork lift traffic. Large colour availability permits highlighting of hazard areas, traffic lanes etc.

Typical Applications:

  • Factories
  • Offices
  • Sports Stadiums
  • Schools
Coverage: Approximately 36m² per 4.5 litre. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

Compliance: Firwood 2750 has been tested for fire resistance to BS EN ISO 9238-1:2010 Fire test for the determination of the burning behaviour of floorings and BS EN ISO 11925-2:2010 Ignitability of building products subject to a direct impingement of flame. Conforms to the Indoor Air Quality requirements of France Class A+, German and Belgian Standards.

Complies with "the VOC in Paints, Varnishes & Vehicle Refinishing Products Regulations 2005".EU limit value for this product (cat A/j): 140g / litre (2010).

Slip Resistance (As supplied) Results obtained using BS7976 Four S Pendulum Test:

  • Dry : 70 - Extremely low slip potential
  • Wet : 15 - High slip
Slip Resistance (with the addition of Firwood 204 Aggregate) Results obtained using BS7976 Four S Pendulum Test:

  • Dry 75 - Extremely low slip potential
  • Wet : 70 - Extremely low slip potential
Coverage: Approximately 36m² per 4.5 litre. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

For more information please also see the Flooring products selection guide located in the download tab.

Please refer to Material Safety Data Sheet and Technical Information Sheet prior to the use of this product. See download tab.



Application Methods: Apply by Brush or Roller. Do not flood pour paint.

Colour Availability: Available from stock in over 250 BS 4800 and RAL shades

Pack Size: 4.5 litre composite pack

Coverage: Approximately 36m² per 4.5 litre. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

Drying Time: Concrete floors are typically several degrees colder than the ambient temperature and on cold days drying times will be extended. It is advisable not to apply the product when the ambient temperature falls below 10ºC or the relative humidity exceeds 85%. Keep coated areas dry for a minimum of 24 hours following application.

Surface Dry @ 20ºC: 1.5 hours

Overcoat @ 20ºC:
After 5 hours

Hard Dry @ 20ºC: 24 hours

VOC Content (when mixed): < 50g / litre

Storage: Store in temperature range 5-40ºC

Thinners: Use cold clean water.

Pot Life @ 20ºC: 2 hours when mixed. The times stated show effective life, however, material stays liquid much longer but does not perform satisfactorily. Do not use after stated times. The pot life will be significantly reduced where the mixed paint is used at higher ambient temperatures.



Surface Preparation: Refer to the Technical Data Sheet.

Packaging: Pack Size : 4.5 litre composite packs consisting of Part A: Base , Part B: Cure.
Weight : 1.1 - 1.2kg / litre when mixed (dependent on colour)

Mixing: Add Part B - Cure to Part A - Base and mix thoroughly for approx. 5 mins using a wide bladed stirrer. A wooden batten at least 25mm wide is ideal. After mixing leave for a 5 minute induction time before application.

Directions for Use: Best results are obtained in warm (minimum 15°C), dry conditions with a good through draught. Apply using a brush and/or long pile, double arm roller.

On bare concrete floors it is recommended that the first coat be diluted with up to 10% water by volume prior to application. This will help seal the concrete surface. Once dried, a second coat can be applied at full strength.

On previously painted floors it is recommended that two thin coats be applied rather than one thick coat. This will prolong the life and performance of the coating.

For application onto asphalt,wood,vinyl and other non prorous floors, two coats are recommended without the first coat being thinned down.

Product will darken slightly during curing and should not be over rolled. To avoid variation in shades always roll in the same direction across the whole area the product is being applied to.

Cleaning: Application equipment should be washed immediately after use in clean cold water before the product starts to cure.

Please click here to download the Technical Data Sheet PDF.
Please click here to download the Material Safety Data Sheet for the base component PDF.
Please click here to download the Material Safety Data Sheet for the curing agent PDF.
Please click here to download the Flooring products selection guide PDF.

Bitte klicken Sie hierfür die SDS- BASE CURE
Proszekliknac tutaj,SDS BASE CURE
SDSProsím kliknete zde BASE CURE
Klik hier voorSDS BASE CURE
S'il vous plaîtcliquez ici pourSDS BASE CURE
Si prega di cliccarequiperSDS BASE CURE
Haga clic aquípara SDS BASE CURE
Por favorclique aqui paraSDS BASE CURE


Product Reviews
Good product
By Dan McIntyre from Nottingham on August 7th 2015
review
Just used this on a store room and shop floor. Great gloss finish which went down easily. Applied two coats and it looks great. Purchased because of colour availability. wearing well so far with fork lift running over it.
Don't forget...
Firwood 2700 Two Pack Water Borne Epoxy Floor Seal

From £ 100.20

Sign Up for Email Offers
Close Chat Now boldchat