Firwood 2700 Two Pack Water Borne Epoxy Floor Seal

Durable pigmented and clear floor sealant paint for use in commercial environments. Used on major projects in the UK and overseas





Firwood 2700 Two Pack  Water Borne Epoxy Floor Seal

Step 1. Click on required shade

Actual colors may vary from the color on your screen due to monitor color restrictions. Always use a shade card for colour matching purposes.

Step 2. Select Options

£89.20 each [+VAT]
+ 89 Loyalty Points
Volume discounts available

5+ for £83.25 each [+VAT]

Add to wishlist

Professional Users - Please register for a trade account for regular purchases. Click here to apply for an account.

A multipurpose water borne two pack epoxy gloss floor seal. It can also be used as an anti-slip coating with the addition of the fine aggregate included with the product. Based on a solvent free epoxy system, this coating has excellent resistance to chemicals, water, oils, greases and mechanical abrasion. Available in 9 colours.

Suitable for use on concrete, stone and asphalt surfaces and is ideal for use in areas of heavy traffic. When used with the aggregate can also be applied to ceramic tiles to produce an anti-slip surface. Ideal for areas requiring extra traction where potential slip hazards exist. Will withstand power washing when fully cured.

  • Low odour, water borne epoxy system
  • Use as full gloss or with an anti slip aggregate to reduce the risks of accidents
  • Hard wearing. Suitable for vehicles and fork lifts
  • Approved for fire resistance & indoor air quality
  • Easy to apply. Adheres to concrete, steel and ceramic tiles
Coverage: Approximately 8 - 10m² per 1 litre. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.
Typical applications:

  • Factory Floors
  • Warehouses
  • Workshops
  • Showrooms
  • Production Areas
  • Parking Areas
  • Schools
Slip Resistance. Results obtained using BS7976 Four S Pendulum:
  • Dry : 70 - Extremely low slip potential
  • Wet : 15 - High slip potential
Slip Resistance (with the addition of anti-slip Aggregate) Results obtained using BS7976 Four S Pendulum Test:
  • Dry 75 - Extremely low slip potential
  • Wet : 70 - Extremely low slip potential
Compliance: Complies with “the VOC in Paints, Varnishes & Vehicle Refinishing Products Regulations 2005". EU limit value for this product (cat A/j): 140g / litre (2010)

Complies with the indoor air quality requirements of: French regulation of March 23, 2011 (décret DEVL1101903D) and of April 19, 2011 (arrêté DEVL1104875A). Class A+ erman Regs. -DIBt (October 2010) and AgBB (June 2012). Belgian Regs - The tested product complies with the requirements of the Royal Decree for establishing threshold levels for the emissions to the indoor environment from construction products for certain intended uses (Draft December 2012). Conforms to Indoor Air Quality Requirements of France, Class A+, Belgium & Germany. Fire Resistant to BS EN ISO 9239-1 2002

For more information please also see the Flooring products selection guide located in the download tab.

Please refer to Material Safety Data Sheet and Technical Information Sheet prior to the use of this product. See download tab.



Application Methods: Apply product by brush or double arm roller.Do not flood pour paint onto substrate.

Colour Availability: White, Coniston Blue, Medium Green, Yellow, Mid Grey, Beige, Tile Red, Black & Clear

Pack Size: 5 and 10 litre composite packs

Drying Time @ 20ºC: Drying times will be extended at low temperatures . Do not apply when ambient temperature falls below 10ºC or relative humidity exceeds 85%.

Surface Dry @ 20ºC : 8 - 12 hours

Hard Dry @ 20ºC: 24 hours

Over Coat @ 20ºC: After 24 hours. Foot traffic can be allowed on the coated area after 24 hours. Heavier traffic can be allowed on the coated area after 4 days with full cure achieved after 7 days.

Coverage: Approximately 8 - 10m² per 1 litre. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

Flash Point: Not applicable

VOC Content (as supplied): Max 50g / litre when mixed

Storage: Store in temperature range 5-40ºC

Thinners: Use clean cold water

Pot Life @ 20ºC: 2 hours when mixed. The times stated show effective life, however, material stays liquid much longer but does not perform satisfactorily. Do not use after stated times. The pot life will be significantly reduced where the mixed paint is used at higher ambient temperatures.







Surface preparation: Refer to the Technical Data Sheet.

Mixing Ratio: Pigmented shades - Base : Curing Agent 1:2 by volume. Clear finish - Base : Curing Agent 1:3.5 by volume. Part C : Non-slip grit, add when required.

Packaging: 10 litre composite packs consisting of Part A: Cure, Part B: Base, Part C: Anti-slip grit.

Mixing: Add Part B - Base to Part A - Cure and mix thoroughly for approx. 5 mins using a wide bladed stirrer. A wooden batten at least 25mm wide is ideal. After mixing leave for a 5 minute induction time before application. For anti-slip surfaces, add Part C to the above mixture and ensure the grit is evenly dispersed throughout the mix. The anti-slip mixture need only be used on the final coat of paint.

Directions for Use:
Best results are obtained in warm (minimum 15°C), dry conditions with a good through draught. Apply using a brush and/or long pile, double arm roller.

On bare concrete floors. It is recommended that the first coat be diluted with up to 10% water by volume prior to application. This will help seal the concrete surface. Once dried, a second coat can be applied at full strength.

On previously painted floors it is recommended that two thin coats be applied rather than one thick coat. This will prolong the life and performance of the coating.

For application onto asphalt,wood,vinyl and other non prorous floors. Two coats are recommended without the first coat being thinned down.

Product will darken slightly during curing and should not be over rolled. To avoid variation in shades always roll in the same direction across the whole area the product is being applied to.

Cleaning: Application equipment should be washed immediately after use in clean cold water before the product starts to cure.







Please click here to download the Technical Information Sheet PDF.
Please click here to download the Material Safety Data Sheet for the base component PDF.
Please click here to download the Material Safety Data Sheet for the curing agent PDF.
Please click here to download the Flooring products selection guide PDF.

Bitte klicken Sie hierfür die SDS- BASE CURE
Proszekliknac tutaj,SDS BASE CURE
SDSProsím kliknete zde BASE CURE
Klik hier voorSDS BASE CURE
S'il vous plaîtcliquez ici pourSDS BASE CURE
Si prega di cliccarequiperSDS BASE CURE
Haga clic aquípara SDS BASE CURE
Por favorclique aqui paraSDS BASE CURE

Product Reviews
Don't forget...
Firwood 2201 Two Pack Epoxy Line Marking Paint Composite Pack

From £ 41.60

Firwood 110 Cleaner and Degreaser

From £ 12.15

Double Arm Roller Kit

From £ 29.64

Firwood 2709 Concrete Etching Fluid

From £ 22.05

Sign Up for Email Offers
Close Chat Now boldchat