Firwood 2500 Garage Floor Paint

For garages, store rooms and offices. Easily applied durable water borne floor paint, fast drying with good tyre pick up resistance

Firwood 2500 Garage Floor Paint

Step 1. Click on required shade

Actual colors may vary from the color on your screen due to monitor color restrictions. Always use a shade card for colour matching purposes.

Step 2. Select Options

£36.00 each [+VAT]
+ 36 Loyalty Points
Volume discounts available

5+ for £35.00 each [+VAT]

Add to wishlist

Professional Users - Please register for a trade account for regular purchases. Click here to apply for an account.

Firwood 2500 Garage floor paint is a water based acrylic paint that has good resistance to the various types of spills you may find in a garage i.e. oils, petrol, diesel, greases, lubricating fluids, water, etc. It is a tough, hard wearing paint that possesses good wear resistance to tyre marks and scuffs. Dries to a sheen finish. Firwood 2500 is suitable for use on concrete and asphalt floors. Please refer to technical information sheet for further information on this product. Available as an anti-slip coating with the addition of Firwood 204 - Anti-slip aggregate.

  • Low odour, water borne floor paint
  • Good tyre pick up resistance
  • Hard wearing 8 shades available from stock
  • Adheres to concrete - Easy to apply
Coverage: Approximately 13m² per 1 litre. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

Typical Applications:
  • Garages
  • Workshops
  • Showrooms
Results obtained using BS7976 Four S Pendulum Test:
  • Dry : 46 - Low slip Potential Wet : 20 Highslip potential
Slip Resistance (with the addition of anti-slip Aggregate)Results obtained using BS7976 Four S Pendulum Test:
  • Dry 66 - Extremely low slip potential Wet : 60 - Low slip potential
Compliance: Complies with “the VOC in Paints, Varnishes & Vehicle Refinishing Products Regulations 2005". EU limit value for this product (cat A/i): 140g / litre (2010)

Firwood 2500 has been tested for fire resistance to BS EN ISO 9238-1:2010 and BS EN ISO 11925-2:2010.

For more information please also see the Flooring products selection guide located in the download tab.

Please refer to Material Safety Data Sheet and Technical Information Sheet prior to the use of this product. See download tab.







Application Methods: Apply product by brush or roller using a long pile, double arm roller. Do not flood pour paint onto substrate.

Colour Availability:
White, Coniston Blue, Medium Green, Beige, Yellow, Mid Grey,Tile Red & Black.

Pack Size: 5 litres

Drying Time @ 20ºC: Drying times will be extended at low temperatures . Do not apply when ambient temperature falls below 5ºC or relative humidity exceeds 90%.

Surface dry @ 20ºC : 1 hour

Over Coat @ 20ºC: After 24 hours.

Coverage: Approximately 13m² per 1 litre. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

Flash Point: Not applicable

VOC Content (as supplied): Max 80g / litre when mixed

Storage: Store in temperature range 5-40ºC

Thinners: Use clean cold water







Surface preparation: Refer to the product Technical Data Sheet.

Mixing: Mix thoroughly for approx. 5 mins using a wide bladed stirrer. For anti-slip surfaces, add Firwood 204 - Anti-slip aggregate and ensure the grit is evenly dispersed throughout the mixed paint. (It is advisable to stir the product during application to prevent the aggregate settling).

Directions for Use: Best results are obtained in warm (minimum 15°C), dry conditions with a good through draught. Apply using a brush and/or long pile, double arm roller. On bare concrete floors it is recommended that the first coat be diluted with up to 20% water by volume prior to application. This will help seal the concrete surface. Once dried, a second coat can be applied at full strength. When painting concrete floors check for surface laitance on the concrete prior to application of the paint. If present then treat with Firwood 2709 Concrete Etching Fluid before painting

On previously painted floors it is recommended that two thin coats be applied rather than one thick coat. This will prolong the life and performance of the coating. For wooden flooring allow to dry thoroughly before applying a second coat, if required.

Cleaning: Application equipment should be washed immediately after use in clean cold water.





Please click here to download the Technical Information Sheet PDF.

Please click here to download the Material Safety Data Sheet PDF.

Please click here to download the Flooring products selection guide PDF.

Product Reviews
Garage floor.
By Judith Webster from Surrey on May 22nd 2015
review
Just wanted to thank you for your totally amazing service. Paint arrived at 8am this morning and is already on the garage floor. We are most grateful and appreciative.
Don't forget...
Firwood 2501 Water Borne Traffic Linemarker

From £ 40.00

Double Arm Roller Kit

From £ 29.64

Firwood 204 Anti-Slip Aggregate

From £ 3.84

Sign Up for Email Offers
Close Chat Now boldchat