Firwood 2507 Asphalt Court Paint

Acrylic hard wearing sports court paint for indoor and outdoor use on asphalt and tarmac tennis courts

Firwood 2507 Asphalt Court Paint

Step 1. Click on required shade

Actual colors may vary from the color on your screen due to monitor color restrictions. Always use a shade card for colour matching purposes.

Step 2. Select Options

£41.05 each [+VAT]
+ 41 Loyalty Points

Add to wishlist

Professional Users - Please register for a trade account for regular purchases. Click here to apply for an account.

Firwood Tennis Court Paint is a premium water borne acrylic paint developed for spray application to porous macadam and concrete courts. The tough coating has excellent resistance to rain and UV light. Suitable for both private and commercial courts. Can also be used on netball courts and childrens play areas in internal and external applications. Tennis court paints are normally applied by airless spray equipment. New asphalt should be left a minimum of three weeks before coating. Slip resistance for different sports can be achieved by the addition of various types of additives available from Firwood. Users of these types of products are advised to contact our Product Advisory Service for full information on the coating of tennis and netball courts. •Suitable for application to asphalt, tarmac and concrete. • Available as an anti-slip coating with the addition of Firwood 207 - Anti-slip aggregate. • Use white for the marking of lines. Typical Applications: •Tennis Courts •Netball Courts Slip Resistance. Results obtained using BS7976 Four S Pendulum: • Dry : 40 - Low slip Potential Wet : 20 - High slip potential Slip Resistance (with the addition of anti-slip Aggregate)Results obtained using BS7976 Four S Pendulum Test: •Dry 66 - Extremely low slip potential Wet : 60 - Low slip potential Compliance: Complies with “the VOC in Paints, Varnishes & Vehicle Refinishing Products Regulations 2005”. EU limit value for this product (cat A/i): 140g / litre (2010) Please refer to Material Safety data Sheet and Technical Information Sheet prior to the use of this product. See download tab.

Application Methods:  Can be sprayed with airless spray equipment. Apply product by brush or roller using a long pile, double arm roller where surface profile permits. Do not flood pour paint onto substrate.

Colour Availability:  Tile Red, Med Green, Coniston Blue, White and Black

Pack Size:   5 litres

Drying Time @ 20ºC:   Drying times will be extended at low temperatures . Do not apply when ambient temperature falls below 10ºC or relative humidity exceeds 85%.

Surface dry @ 20ºC :  1 hour

Over Coat@ 20ºC:   After 24 hours. Foot traffic can be allowed on the coated area after within 12 - 24 hours.

Coverage:   Approximately 30m² per 5 litre per coat. Normally 2 coats are required. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

Flash Point:  Not applicable

VOC Content (as supplied):   Max 30g / litre when mixed

Storage:   Store in temperature range 5-40ºC

Thinners:   Use clean cold water

Surface preparation:      Refer to the technical Data Sheet.

Mixing:     Mix thoroughly for approx. 5 mins using a wide bladed stirrer. A wooden batten at least 25mm wide is ideal.

For anti-slip surfaces, add Firwood 207 - Anti-slip aggregate (supplied with product) and ensure the grit is evenly dispersed throughout the mix.

Directions for Use:    Best results are obtained in warm (minimum 15°C), dry conditions with a good through draught. Apply using a brush and/or long pile, double arm roller. For asphalt surfaces apply as supplied without thinning. Ensure you work the product into all voids around the asphalt aggregate but avoid pooling of the paint in such voids.

On bare concrete floors: It is recommended that the first coat be diluted with up to 20% water by volume prior to application. This will help seal the concrete surface. Once dried, a second coat can be applied at full strength.

On previously painted floors: It is recommended that two thin coats be applied rather than one thick coat. This will prolong the life and performance of the coating.

For wooden flooring: Allow to dry thoroughly before applying a second coat, if required.

Cleaning:    Application equipment should be washed immediately after use in clean cold water.

 Please click here to download the Technical Information Sheet PDF.

 Please click here to download the Material Safety Data Sheet PDF.

Product Reviews
Sign Up for Email Offers
Close Chat Now boldchat