Firwood 40 Chemical Resistant Anti-Slip Floor Paint

Single pack epoxy anti-slip floor paint with resistance to mild chemicals and oils

Firwood 40 Chemical Resistant Anti-Slip Floor Paint

Step 1. Click on required shade

Actual colors may vary from the color on your screen due to monitor color restrictions. Always use a shade card for colour matching purposes.

Step 2. Select Options

£37.85 each [+VAT]
+ 37 Loyalty Points
Volume discounts available

5+ for £36.60 each [+VAT]

Add to wishlist

Professional Users - Please register for a trade account for regular purchases. Click here to apply for an account.

An anti-slip floor paint based on an epoxy formulation that dries to a tough durable sheen finish. It has good resistance to water, oils, mild acids and alkalis. The anti-slip properties are produced by the use of organic powder which provides a hard wearing surface whilst is gentle underfoot. Helps provide enhanced safety to potentially slippery areas.

  • Ideal for use on concrete and timber floors
  • Ease of application by brush or roller
  • Contains anti-slip additive
  • Suitable for domestic and light commercial applications
Coverage: Approximately 10m² per litre per coat, normally 2 coats are required Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application

Typical Applications:

  • Store rooms
  • Workshops
  • Retail environments
  • Kennels
Slip Resistance (As supplied)Results obtained using BS7976 Four S Pendulum Test:

  • Dry : 52- Low slip Potential Wet : 40 - low slip potential
Compliance: Complies with “the VOC in Paints,Varnishes & Vehicle Refinishing Products Regulations 2005".EU limit value for this product when used as a binding primer (cat A/h): 750g / litre (2010). When used as a floor paint (catA/i): 500 g/l (2010).

For more information please also see the Flooring products selection guide located in the download tab.

Please refer to Material Safety Data Sheet and Technical Information Sheet prior to the use of this product. See download tab.

Application Methods: Brush or Roller using a long pile, double arm roller.

Colour Availability: Mid Grey, Tile Red and Med Green

Pack Size: 5 litres

Drying Time @ 20ºC: Drying times will be extended at low temperatures . Do not apply when ambient temperature falls below 5ºC or relative humidity exceeds 90%.

Surface dry @ 20ºC : 1.5 hours

Hard Dry@ 20ºC: 5 hours

Over Coat@ 20ºC: After 24 hours

Coverage: Approximately 10m² per litre per coat, normally 2 coats are required Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application

Flash Point: 38ºC

VOC Content (as supplied): Max 499g / litre

Storage: Store in temperature range 5-40ºC

Thinners: Firwood 143 Thinners



Surface Preparation: Refer to Technical Data Sheet on the downloads section for this product. We recommend the use of Firwood 2709 Concrete Etching Fluid when coating concrete floors to remove surface laitance and improve adhesion of the floor paint.

Mixing: Stir well before use. Mix thoroughly for approximately 5 minutes using a wide bladed stirrer.

Directions for Use: Best results are obtained in warm (minimum 15°C), dry conditions with a good through draught.

Mix during use to prevent settling of anti-slip additive.

Apply using a brush and/or long pile, double arm roller.

On bare concrete floors: It is recommended that the first coat be diluted with approx. 10-20% Firwood 143 thinners by volume prior to application. This will act as a binding primer and help seal the concrete surface. Once dried, a second coat can be applied at full strength. Do not flood pour paint onto substrate.

On previously painted floors: Prior to extensive application of this product always check a test patch for compatibility and adhesion. It is recommended that two thin coats be applied rather than one thick coat. This will prolong the life and performance of the coating.

Cleaning: Application equipment should be cleaned immediately after use with Firwood 143 low odour thinners.

Please click here to download the Technical Information Sheet PDF.

Please click here to download the Material Safety Data Sheet PDF.

Please click here to download the Flooring products selection guide PDF.

Product Reviews
Don't forget...
Paint Stirrer

From £ 1.98

Double Arm Roller Kit

From £ 29.64

Firwood 110 Cleaner and Degreaser

From £ 12.15

Firwood 143 Thinners

From £ 17.65

Sign Up for Email Offers
Close Chat Now boldchat