Firwood 2200 Heavy Duty Anti-Slip Coating

Heavy duty anti slip coating for commercial applications that dries fast and is used in sports stadiums, retail outlets and factories

Firwood 2200 Heavy Duty Anti-Slip Coating

Step 1. Click on required shade

Actual colors may vary from the color on your screen due to monitor color restrictions. Always use a shade card for colour matching purposes.

Step 2. Select Options

£90.20 each [+VAT]
+ 90 Loyalty Points
Volume discounts available

5+ for £87.90 each [+VAT]

Add to wishlist

Professional Users - Please register for a trade account for regular purchases. Click here to apply for an account.

A multipurpose epoxy resin coating for the in-situ application of anti-slip surfaces. This product combines a durable solvent free epoxy paint with a heavy duty aggregate dressing selected for its anti-slip properties. Has excellent resistance to water, chemicals and abrasion. Quick and easy to apply thus minimising long term closure of coated areas.

Suitable for use on concrete, brick, stone, asphalt and suitably abraded ceramic tiles. Complies with building regulations regarding access for the disabled. The two pack coating is applied then the aggregate broadcast by hand and bedded in before the coating cures.

  • Low odour, solvent free 100% solids epoxy resin system
  • Suitable for use on concrete, brick, stone, asphalt and ceramic tiles
  • Rapid drying
  • High slip resistance
  • Available from stock in 6 shades
Coverage: Approximately 5m² per pack. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

Typical Applications:
  • Steps
  • Ramps
  • Walkways
  • Footbridges
  • Sports Stadia
  • Retail Parks
  • Disabled Access
Slip Resistance (As supplied)Results obtained using BS7976 Four S Pendulum Test:
  • Dry : 81 - Extremely low slip Potential Wet : 68 - Extremely low slip Potential
Compliance: Complies with “the VOC in Paints, Varnishes & Vehicle Refinishing Products Regulations 2005". EU Limit Value for this product (cat.A/j): 500g/l (2010). This product contains max 5 g/l VOC

For more information please also see the Flooring products selection guide located in the download tab.

Please refer to Material Safety Data Sheet and Technical Information Sheet prior to the use of this product. See download tab.



Application Methods: Apply product by brush or roller then immediately scatter aggregate evenly over surface. Allow to dry for at least 4 hours and then brush off excess aggregate.

Colour Availability: White, Yellow, Mid Grey, Med Green, Brown & Black.

Pack Size: 10 kgs packs

Drying Time @ 20ºC: Drying times will be extended at low temperatures . Do not apply when ambient temperature falls below 10ºC or relative humidity exceeds 85%.

Surface Dry @ 20ºC : Not applicable

Hard Dry @ 20ºC: 4 -6 hours. Foot traffic can be allowed on the coated area after 24 hours. Heavier traffic can be allowed on the coated area after 48 hours with full cure achieved after 7 days.

Coverage: Approximately 5m² per pack. Coverage can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.

Flash Point: 100ºC

VOC Content (as supplied): VOC Free

Storage: Store in temperature range 5-40ºC

Cleaning Thinners: Firwood 113 Thinners

Pot Life @ 20ºC: 30 minutes when mixed. The pot life will be significantly reduced where the mixed paint is used at higher ambient temperatures.

Surface preparation: Refer to the technical Data Sheet.

Mixing Ratio: Base : Curing Agent 2.7:1 by volume. Part C: Non-slip grit, add when required.

Packaging: Pack Size : 10 kg composite pack consisting of Part A: Base, Part B: Cure, Part C: Non-slip grit.

Mixing: As the pot life for this product isonly 30 minutes, the components should only be mixed together when ready to apply the coating. Ensure all surface preparation is done before mixing. Add Part B - Cure to Part A - Base and mix thoroughly for approx. 5 mins using a wide bladed stirrer. A wooden batten at least 25mm wide is ideal. Caution: The base paint cures by exothermic reaction with the curing agent. After initial mixing the base paint will increase significantly in temperature. The product is usable in this state but care should be taken in its handling. Do not leave the can on any surface that might be affected by high temperatures and hold the can by its nylon handle.

Directions for Use: Best results are obtained in warm (minimum 15°C), dry conditions with a good through draught.

Mask off the areas to be coated as applicable.

Apply the mixed base paint to the surface using a brush and/or short nap, synthetic roller. Once the coating has been applied,immediately broadcast the coloured aggregate (Part C) by hand over the coating ensuring all areas are well covered.

Remove masking tape whilst coating is still wet.

After the coating has cured, remove excess aggregate with a soft brush.

Cleaning: Application equipment should be disposed of after use or cleaned immediately with Firwood 113 Thinners.

Ongoing slip resistance is dependent on the coated floor being kept clean of contaminants such as greases, leaves etc. In wet icy conditions then the anti slip properties will be less effective where ice builds up on the coating.



Please click here to download the Technical Information Sheet PDF.

Please click here to download the Material Safety Data Sheet for the base component PDF.

Please click here to download the Material Safety Data Sheet for the base component PDF.

Please click here to download the Flooring products selection guide PDF.

Product Reviews
Don't forget...
Firwood 110 Cleaner and Degreaser

From £ 12.15

Firwood 2709 Concrete Etching Fluid

From £ 22.05

Firwood 40 Chemical Resistant Anti-Slip Floor Paint

From £ 37.85

Firwood 2210 Two Pack Fast Dry Epoxy Seal

From £ 110.00

Sign Up for Email Offers
Close Chat Now boldchat